{'Description':'The state requested for the element. This information will be placed into the RequestedState property of the instance if the return code of the RequestStateChange method is 0 ('Completed with No Error'), or 4096 (0x1000) ('Job Started'). Refer to the description of the EnabledState and RequestedState properties for the detailed explanations of the RequestedState values.','ModelCorrespondence':['CIM_EnabledLogicalElement.RequestedState'],'ValueMap':['2', '3', '4', '6', '7', '8', '9', '10', '11', '..', '32768..65535'],'Values':['Enabled', 'Disabled', 'Shut Down', 'Offline', 'Test', 'Defer', 'Quiesce', 'Reboot', 'Reset', 'DMTF Reserved', 'Vendor Reserved']}
{'Description':'May contain a reference to the ConcreteJob created to track the state transition initiated by the method invocation.'}
TimeoutPeriod
datetime
2
✓
-
{'Description':'A timeout period that specifies the maximum amount of time that the client expects the transition to the new state to take. The interval format must be used to specify the TimeoutPeriod. A value of 0 or a null parameter indicates that the client has no time requirements for the transition. If this property does not contain 0 or null and the implementation does not support this parameter, a return code of 'Use Of Timeout Parameter Not Supported' shall be returned.'}
{'Description':'The power state to set.','ValueMap':['1', '2', '3', '4', '5', '6'],'Values':['Full Power', 'Power Save - Low Power Mode', 'Power Save - Standby', 'Power Save - Other', 'Power Cycle', 'Power Off']}
Time
datetime
1
✓
-
{'Description':'Time indicates when the power state should be set, either as a regular date-time value or as an interval value (where the interval begins when the method invocation is received.'}
'An array of octets holding additional error information. An example is ECC Syndrome or the return of the check bits if a CRC-based ErrorMethodology is used. In the latter case, if a single bit error is recognized and the CRC algorithm is known, it is possible to determine the exact bit that failed. This type of data (ECC Syndrome, Check Bit or Parity Bit data, or other vendor supplied information) is included in this field. If the ErrorInfo property is equal to 3, "OK", then AdditionalErrorData has no meaning.'
'The ending address, referenced by an application or operating system and mapped by a memory controller, for this Memory object. The ending address is specified in KBytes.'
'An integer enumeration indicating the memory access operation that caused the last error. The type of error is described by the ErrorInfo property. If the ErrorInfo property is equal to 3, "OK", then this property has no meaning.'
'Specifies the address of the last memory error. The type of error is described by the ErrorInfo property. If the ErrorInfo property is equal to 3, "OK", then this property has no meaning.'
'Data captured during the last erroneous mebmory access. The data occupies the first n octets of the array necessary to hold the number of bits specified by the ErrorTransferSize property. If ErrorTransferSize is 0, then this property has no meaning.'
'The ordering for data stored in the ErrorData property. "Least Significant Byte First" (value=1) or "Most Significant Byte First" (2) can be specified. If ErrorTransferSize is 0, then this property has no meaning.'
'An integer enumeration describing the type of error that occurred most recently. For example, single (value=6) or double bit errors (7) can be specified using this property. The values, 12-14, are undefined in the CIM Schema since in DMI, they mix the semantics of the type of error and whether it was correctable or not. The latter is indicated in the property, CorrectableError.'
'Specifies the range, in bytes, to which the last error can be resolved. For example, if error addresses are resolved to bit 11 (ie, on a typical page basis), then errors can be resolved to 4K boundaries and this property is set to 4000. If the ErrorInfo property is equal to 3, "OK", then this property has no meaning.'
'The time that the last memory error occurred. The type of error is described by the ErrorInfo property. If the Error Info property is equal to 3, "OK", then this property has no meaning.'
'The size of the data transfer in bits that caused the last error. 0 indicates no error. If the ErrorInfo property is equal to 3, "OK", then this property should be set to 0.'
'The beginning address, referenced by an application or operating system and mapped by a memory controller, for this Memory object. The starting address is specified in KBytes.'
'Boolean indicating whether the address information in the property, ErrorAddress, is a system-level address (TRUE) or a physical address (FALSE). If the ErrorInfo property is equal to 3, "OK", then this property has no meaning.'
'ErrorMethodology for Memory is a string property that indicates whether parity or CRC algorithms, ECC or other mechanisms are used. Details on the algorithm can also be supplied.'